Removing Liner From Motorcycle Tank

I used a long screwdriver to scrape what I could of my Kreem liner in the tank. I came across a old chopper I did in 1980.

How To Remove A Dent From A Motorcycle Gas Tank Ultimate Guide

Jump to Latest Follow.

Removing liner from motorcycle tank. Talked to a mechanic who has been around since JC came to earth and the first question he asked what was the condition of the fuel. Only problem that I am now faced with is every so often the left Bing carburetor starts to ps out fuel. This video is a part two of the how to remove rust from your gas tank a short series on how to restore a motorcycle gas tank.

As some of you know I bought a Yellow 1989 R100RT sight in seen. This is the process I followed to remove a Kreem liner and POR-15 my tank. I cant buy a new tank until I replace my job.

Acetone and a few pounds of drywall screws lots of sharp edges have always worked well for me. Id like to remove the old lining clean the tank and reline it. I was trying to hurry so i can get to the gym on time.

When I winterized my 86 R80 I found some loose liner material. This chemical not only removes virtually any polymer coating it also promotes rust so youll need to acid-etch the tank afterward to be sure that all traces of rust are gone too. KBS - see reply 3 I used a Kreem kit w no problems many many years ago - the tank liner is still there.

By jenkinov October 10 2011 in Motorcycles. Use short screws they get into the corners better. Resist the urge to re-Keeme it.

It is a good idea to keep the KBS Strip in contact with the tank liner for a few hours and then drain while capturing the KBS Strip so you can use it again. It was a welded mounting tab Now the question is how t. We remove rust and mystery contaminants then install a permanent liner that protects your tank from modern fuel and the damage it causes.

From there I took the tank to a radiatorfuel tank repair shop that boiled out the tank and recoated it with the RedKote hard shell liner. Let it soak for a while to soften. Interior is beautiful with very minor surface rusting.

The dents arent really that bad. Get the methylene chloride out of the tank as soon as the old coating has lifted rinse it thoroughly then dry out the inside with heat compressed air. I had Kreem do this in my old SR500 with the tank rusting again.

And because our process is completely internal its done without affecting your paint. I bought a used aluminum gas tank that someone had put a liner inside that didnt adhere very well and is peeling. Has anyone ever removed theirs.

But its too cold for body work. Also being an 86 my bike is blessed with the crappy funnel and flap under the gas cap. It hits the pavement at high velocity.

Still just like I built it. I swished water and 20 long drywall screws in the tank and rinsed. Discussion on V-Twin Harley Davidson motorcycles including Dyna Electra Glide Softail Sportster and more.

Same paint and all. Not going to worry about the exterior paint on either tank as both will be repainted after the POR jobs. If you prep the tank use the product right any of the kits will work.

The 83 tank is pristene - other than a minor dent in the side. I looked in the tank and saw the old Kreme tank liner I had put in it when I noticed toe tank had a pinhole after I had just had it painted. KBS Strip should take out the old liner.

Smashes up the whole right side and the rear of the left. How to remove gas tank sealer. Has anyone removed the BMW factory lining.

If you do that a few times on each side you should be able to get all of the old liner out and then proceed to the KBS 3-Step Tank Sealing System. After replacing just about every seal on the engine and transmission it is now oil tight. Triumph tank - removal of old tank linerAn experiment.

I was able to get ahold of some of it with pliers and pull it out. Arent there liner removal kits. Hey guys anyone have any ideas for removing old Creame Tank Liner from Vintage tanks clean out the tanks and then will renew the liner.

Removing gas tank liner. My hands and the tank are wet and soapy. GTL has perfected the process of cleaning and lining motorcycle gas tanks.

I have also noticed some rust particles in the float bowls. I have tried several different tank lining products and they have all failed. Heres a KBS testimonial.

Wrapping tank to protect paint plugging petcock and tank chains safety gear. Triumph tank - removal of old tank linerAn experiment. Then comes PORing that tank and the 83 tank I picked up from Leather last Fall.

I placed a rubber stopper over the petcock hole that I purchased at Autozone and a plastic bag under the gas cap. Corners are nice solid. Id wager that the tank wasnt prepped as per the instructions andor the product wasnt used correctly.

Yuichi On Instagram K1 Cb750four Cb750 Cb750k Cb400 Honda Cb Japanese Motorcycle Honda 750

How To Clean Rust Out Of A Motorcycle Gas Tank On Countersteer

Remove Install Harley Davidson Fuel Gas Tank Motorcycle Biker Podcast Youtube

You Re Looking At What Used To Be A Very Rusty Gas Tank For A 79 Kawasaki Kz1300 This Is What It Looks Like After We Cleaned How To Remove Rust Gas

Pin On Products

Ims 10 Gallon Fuel Tank For Klr650 Adventure Motorcycle Gear Rat Bike Klr 650

How To Fix A Dent In A Motorcycle Gas Tank That Works Every Time Motorcycle Habit

Motorcycle Gas Tank Rust Removal Solutions Motorcyclezombies Com

Motorcycle Dent Removal Harley Davidson Sportster Gas Tank Paintless Dent Repair Youtube

Ims 10 Gallon Fuel Tank For Klr650 Adventure Motorcycle Gear Adventure Motorcycling Rat Bike

Electrolytic Tank Cleaning Method By Jon Pardue Homemade Electrolytic Tank Cleaning Method Utilizing A Length Of Chain Was Tank How To Clean Rust Bike Tank